step by setp how to tune POS1060
as well all know to tune POS1060 we need
Vcc=10 volte
current=?(i m applying 1um with 23 V dc ts not wroking)
V-tune= 17 to 23 V peck to peck 
what you all mean by this when you are saying we need 10 to 20khz signal needed
plesae make it clear for all of as here having this problem i request both of you
richy_64 and kleiner-onkel
Ok, let´s see what the datasheet says to get the POS1060 working.
Unfortunately i don´t have a POS1060 for testing.
-Suppy voltage: 10V (12V maximum) at Pin 1.
Current: up to 30mA
-Tuning voltage: 1...20V (25V maximum) at Pin 8
-Ground at Pins 3,4,5,6,7
-RF Output at Pin 2.
Attention: The pin configuration is non-standard!
Check the picture below!!! Very confusing.
@kleiner onkel, your circuit diagram of your jammer 1 is not correct.
----------------
Tuning voltage:
I would start with sawtooth 16...20V.
>>V-tune= 17 to 23 V peck to peck what you all mean by this when you are saying we need 10 to 20khz signal needed
It´s not funny to explain it again and again... 
This is basic knowledge in electronics... everyone on this board should know this...
This evening i will add some pictures to my sawtooth generator, it´s much easier to explain with pictures.
@imgemini, shazia, imran....
Building a circuit is much easier when you know how it works before you try to build it. Do you all know how a jammer works? I´m not sure about that... 
hi
plesae richy_64 explain it . for as just once,s . bcoz its :confusing .....
Re: step by setp how to tune POS1060
hi friend
plesae dont mind my qustions . all i need is help . if u dont help as then there is no place to go . all of as here having this problem . what is wrong if your words make some ones life easy . three of as having here same problem .as shazia writes. plesae try to understand and plesae dont mind . the work that you are doing is great .
puond to be germen........
hallo Freund plesae kümmern sich nicht um meine qustions. alle, die ich benötige, ist Hilfe. wenn u nicht helfen, da dann es keinen Platz gibt, zum zu gehen. alle von als dieses Problem hier, habend. was Unrecht ist, wenn Ihre Wörter einige eine Leben einfach bilden. drei von wie hier die gleichen Problem as haben, die shazia plesae Versuch schreibt, um zu verstehen und plesae kümmern sich nicht. die Arbeit, die Sie erledigen, ist groß
hi
today i apply 18 to 20 V DC with 20Khz and 10AC but anthing happent
what will be the best tune signal that will work for that and . if harmonie siganls are there then what should i do ... 
plesae reply friend i am very near to finsh my jammer 
My last try...
The easiest way to check the function of the vco (POS1060):
Connect a power supply to the vco (8-10V, for example a 9V battery) AND to the tune input, too. So Pin 1 and 8 have 9V.
Then connect a spectrum analyser or a frequency counter at the output (Pin 2). There has to be a frequency around 900MHz.
If you have not, your might have connected the POS1060 wrong or it was damaged during previous experiments.
There is nothing more to say!
>>i am very near to finsh my jammer
NO, you´re just at the beginning!!
__________________________________________________
"Ich liebe es wenn ein (Schalt-)Plan funktioniert."
hi
at last my jammer work........ 
well the problem was the test circuit was not working . today i connect PA with it and that work fine........... 
so i will not support the idea of test circuit ..
thx,s u both of u ............. i will upload circuit tomarow
Please upload the circuit ASAP......thanks.
Re: step by setp how to tune POS1060
>>...the problem was the test circuit was not working, today i connect PA with it and that work fine...... so i will not support the idea of test circuit ..
Ridiculous.
With no experience you have to do little steps...
Anyway, i hope you use your new toy with care.
hi
one qustion in my mind and all other are asking that why sewooth signal.......why its betther the other to sweep frequency
the jamemr APPLICATIONS it can be use in
Gas stations
Hospitals
just think y jammer ,s RF signals are better then mobile phone signals
